Wrong warmstart parameters

I am trying to configure a CIFX50-RE as slave in an EtherCat network consisting of a master and a slave. The firmware version of the master is 1.0.0 (build 630).

A screen shot with the warmstart parameters is attached.

The master is configured with the xml file from the EtherCat configurator and a
Set Bus Param packet is send. When the IO monitor of the slave is opened in the lower left corner there is an error message:

0x800C0012 (device is not running) rinning flag failed.

here is the log file of the cifx driver:

03.09.2007 16:55:14.453:----- CIFx Driver Log started ---------------------
03.09.2007 16:55:14.453:Driver Id: cifXDriver B0.921

03.09.2007 16:55:14.453:New device is a PCI device and will be reset!
03.09.2007 16:55:15.625:Bootloader was downloaded and started successfully!
03.09.2007 16:55:15.625:Firmware download, checking / starting: CHANNEL #0, 1 file(s)
03.09.2007 16:55:16.343:Successfully downloaded the firmware to device 'C:\Program Files\cifX Device Driver\1250100_20130\Channel0\ecscifx50.mod'!
03.09.2007 16:55:16.343:Firmware download, checking / starting: CHANNEL #1, 0 file(s)
03.09.2007 16:55:16.343:Firmware download, checking / starting: CHANNEL #2, 0 file(s)
03.09.2007 16:55:16.343:Firmware download, checking / starting: CHANNEL #3, 0 file(s)
03.09.2007 16:55:16.343:Firmware download, checking / starting: CHANNEL #4, 0 file(s)
03.09.2007 16:55:16.343:Firmware download, checking / starting: CHANNEL #5, 0 file(s)
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#0, 0 file(s)!
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#1, 0 file(s)!
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#2, 0 file(s)!
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#3, 0 file(s)!
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#4, 0 file(s)!
03.09.2007 16:55:16.343:Configuration download, checking / starting: CHANNEL#5, 0 file(s)!
03.09.2007 16:55:18.843:System channel is READY!
03.09.2007 16:55:18.843:Successfully started firmware!
03.09.2007 16:55:18.843:Reading Channel Info on Channel#0 (DPM Start Offset=0x00000300 Length=0x00003D00)
03.09.2007 16:55:18.843:-------------------------------------------------------------------------
03.09.2007 16:55:18.843:Control block found (Channel=0, Block=0, Offset=0x00000008, Len=0x0008)
03.09.2007 16:55:18.843:Common Status block found (Channel=0, Block=1, Offset=0x00000010, Len=0x0040)
03.09.2007 16:55:18.843:Extended Status block found (Channel=0, Block=2, Offset=0x00000050, Len=0x01B0)
03.09.2007 16:55:18.843:Output Mailbox found (Channel=0, Block=3, Offset=0x00000200, Len=0x0640)
03.09.2007 16:55:18.843:Input Mailbox found (Channel=0, Block=4, Offset=0x00000840, Len=0x0640)
03.09.2007 16:55:18.843:I/O Output Subblock found (Channel=0, Block=5, Offset=0x00001000, Len=0x1680)
03.09.2007 16:55:18.843:I/O Input Subblock found (Channel=0, Block=6, Offset=0x00002680, Len=0x1680)
03.09.2007 16:55:18.843:I/O Output Subblock found (Channel=0, Block=7, Offset=0x00000E80, Len=0x0040)
03.09.2007 16:55:18.843:I/O Input Subblock found (Channel=0, Block=8, Offset=0x00000EC0, Len=0x0040)
03.09.2007 16:55:18.843:-------------------------------------------------------------------------
03.09.2007 16:55:20.843:Device successfully created for channel = 0

03.09.2007 16:55:20.843:Error opening warm start file!
03.09.2007 16:55:20.843:No warm start parameter found or available!

Vesselin